Ivoclar Multilink N System Composite Pack

Description

Key Features

• Universal Application
• Strong and Durable Bond
• Easy Cleanup
• Self-Etch Adhesive
• Compatibility with Various Materials
• User-Friendly Handling
• Coordination with Ivoclean and Monobond N
• Proper Storage Conditions

Specifications

Composition:

• Monomer Matrix: Dimethacrylate and HEMA (hydroxyethyl methacrylate).
• Inorganic Fillers: Barium glass, ytterbium trifluoride, and spheroid mixed oxide.
• Particle Size: Ranging from 0.25 to 3.0 µm with a mean particle size of 0.9 µm.
• Total Volume of Inorganic Fillers: Approximately 40% of the material consists of inorganic fillers.

Storage Temperature:

• Recommended storage temperature: 2-8°C (36-46°F).

Packaging

• 1 x 6g Multilink N
• 1 x 3g Multilink N Primer A
• 1 x 3g Multilink N Primer B
• 1 x 5g Monobond N

Directions for Use

Removal of Temporary Restoration and Cleaning of the Cavity:

• Remove any residue of the temporary luting cement from the cavity or preparation using a polishing brush and an oil and fluoride-free cleaning paste.
• Rinse with a water spray and dry with air that is free of water and oil. Avoid over-drying.

Try-In of the Restoration and Drying:

• Check the shade, fit, and occlusion of the restoration.
• Make necessary adjustments with fine diamonds if required. Be cautious with fragile ceramic objects.
• If using an adhesive luting protocol with composites, ensure safe isolation of the operating field (e.g., rubber dam or cotton rolls with a saliva ejector).

Pre-Treatment of the Restoration:

• Rinse the restoration with a water spray and dry it with oil-free air.
• Thoroughly coat the bonding surface of the restoration with Ivoclean using a micro brushor brush.
• Allow Ivoclean to react for 20 seconds, rinse with water spray, and dry with oil-free air.
• For certain restorations (e.g., lithium disilicate glass ceramics or zirconium oxide ceramics), apply Monobond N to cleaned surfaces using a brush or micro brush. Allow it to react for 60 seconds and disperse with a strong stream of air.

Mixing of Multilink N Primer A and Multilink N Primer B:

• Mix the two primer liquids (Multilink N Primer A and B) in a 1:1 ratio (e.g., 1 drop Primer A and 1 drop Primer B). The mixed primer is solely self-curing and must be applied within 10 minutes.

Application of the Mixed Multilink N Primer A/B:

• Apply the mixed Multilink N Primer A/B onto the entire bonding surface using a micro brush, starting with the enamel surface, and scrub it in for 30 seconds.
• Disperse excess with blown air. No light-curing is necessary.

Application of Multilink N to the Restoration:

• Place a new automix tip on the syringe for each application.
• Dispense Multilink N from the automix syringe and apply the desired amount to the restoration.
• Replace the mixing tip with a new one before the next use.

Placement of the Restoration and Removal of Excess Cement:

• Seat the restoration in place and secure it.
• Remove excess material immediately with a micro brush, brush, foam pellet, dental floss, or scaler.
• For self-curing with additional light-curing (quarter technique), light-cure excess cement in quarter segments.
• Remove excess rapidly in challenging areas (proximal areas, gingival margins, pontics).
• Light-cure all the margins again for 20 seconds.

Finishing of the Restoration:

• Finish the cement joints with preparation diamonds if necessary.
• Polish restoration margins/cement joints with suitable polishers and finishing and polishing strips.
• Check occlusion and function and make adjustments if necessary.

Additional Information

Country of Origin: Liechtenstein

Manufacturer:
Ivoclar Vivadent AG
Bendererstrasse 2, 9494 Schaan, Liechtenstein

Packer:
Ivoclar Vivadent AG
Bendererstrasse 2, 9494 Schaan, Liechtenstein

Imported By:
Ivoclar Vivadent India Pvt. Ltd.
Ground Floor and 1st Floor, Khandsa Village, Gurugram, Haryana, India
Phone: +91 72899 99456

Warranty & Service

• Warranty is not applicable for this product.