Labodent Zirconia Ceramic Blank ST-C | A1 Shade | 14mm | Pre-Shaded CAD/CAM Disc

Description

Labodent Zirconia Ceramic Blanks ST-C (A1 Shade) are pre-shaded, standard-translucency zirconia CAD/CAM discs used to mill aesthetic dental restorations such as crowns, bridges, copings, inlays, onlays, and veneers. Each 98 mm disc is pre-pigmented to the A1 VITA Classic shade, so restorations achieve consistent colour straight after sintering with no coloring liquid required.

The ST-C designation stands for Standard Translucency with C-type disc geometry. The zirconia offers 43% translucency, a flexural strength of 1,100 MPa, density of ≥6.0 g/cm³, hardness of Hv10 1250, and fracture toughness of ≥3 MPa·m½, sintering at approximately 1,510°C. This balance of strength and lifelike translucency makes ST-C A1 well suited to both anterior and posterior single units and multi-unit bridge frameworks.

The A1 shade is available in four disc heights — 10 mm, 12 mm, 14 mm 16 mm 18mm, 20mm, 22mm, 25mm — so you can match disc thickness to restoration height and the number of units milled per disc. Taller 14–16 mm discs suit full-contour molar crowns and bridges, while 10–12 mm discs are economical for anterior and single-unit work. For other shades, see the A2 shade and A3 shade discs in the same ST-C range.

These open-system discs are compatible with all major CAD/CAM milling units used in dental laboratories and chairside setups. Compared with lithium disilicate (such as emax), ST-C standard-translucency zirconia provides higher strength for posterior and long-span cases while keeping natural aesthetics on visible teeth. Manufactured by Labodent, these CAD/CAM zirconia blanks give dental laboratories a reliable, cost-effective milling material starting at ₹1,850 — explore more dental laboratory and CAD/CAM supplies on Dentalkart.

Key Features

• No coloring liquid required, consistent shade every time
• Natural, lifelike tooth appearance
• Long-lasting, fracture-resistant restorations
• Safe and comfortable for intraoral use
• Works with all major milling systems
• Optimal density at ~1,510°C
• Crowns, bridges, implants, copings & more

Specifications

• Shade: A1 (VITA Classic)
• Translucency: 43%
• Flexural Strength: 1,100 MPa
• Density: ≥6.0 g/cm³
• Hardness: (Hv10) 1250
• Fracture Toughness: ≥3 MPa·m½
• Sintering Temperature: ~1,510°C
• Diameter: 98
• ZrO₂ + HfO₂ + Y₂O₃: ≥99%
• Y₂O₃: 5% ± 0%
• Al₂O₃: ≤1.5%

Packaging

• Pack of 1 

Directions for Use

Case Planning

• Receive the dental impression or digital scan
• Determine the restoration type (crown, bridge, implant, etc.)
• Select the appropriate blank size and thickness based on the case

CAD Design

• Import the digital scan into CAD software
• Design the restoration – crown, bridge, inlay, onlay or crown supported restoration 
• Verify margins, contacts, and occlusion digitally

CAM Milling

• Mount the ST-C A1 blank securely into the milling machine
• Select the correct milling parameters for zirconia
• Mill the restoration using your CAD/CAM system

Pre-Sintering Finishing

• Remove the milled restoration carefully from the blank
• Trim and adjust margins in the pre-sintered (soft) state
• Clean the restoration with a brush and distilled water

Sintering

• Place the restoration in a sintering furnace
• Sinter at ~1,510°C following the recommended firing cycle
• Allow to cool gradually inside the furnace

Post-Sintering Finishing

• Check fit, margins, and occlusion on the model
• Polish or glaze the restoration as required
• Apply staining if additional characterization is needed

Final Delivery

• Verify shade accuracy against A1 VITA Classic
• Inspect restoration for cracks or defects
• Deliver the finished restoration to the dentist for fitting

Additional Information

Country of Origin: India

Manufacturer:
Vasa Denticity Limited
Dock No. IN7 & IN8, Shed 1, Pataudi Road, Near Adani Logistics Park, ICD Patli, Killa No. 14/2, Gurugram – 122503, Haryana, India
Phone: +91 72899 99456

Packer:
Vasa Denticity Limited
Dock No. IN7 & IN8, Shed 1, Pataudi Road, Near Adani Logistics Park, ICD Patli, Killa No. 14/2, Gurugram – 122503, Haryana, India
Phone: +91 72899 99456

Marketed By:
Vasa Denticity Limited
Dock No. IN7 & IN8, Shed 1, Pataudi Road, Near Adani Logistics Park, ICD Patli, Killa No. 14/2, Gurugram – 122503, Haryana, India
Phone: +91 72899 99456

Warranty & Service

• Warranty is not applicable for this product.