Kids-e-Dental Bands with tube attached Size 35.5

Description

Kids-e-Dental Bands comes in universal band design with attached tube for connecting space maintainer wires to prevent pre mature loss of space.

Space Maintainer Wires which can be used along with these Bands :

• Straight Loops
• Curved Loops
• Distal Shoe

Band and Loop Space Maintainers – 

Before the new molar erupts, band and loop spacers make it a point to leave ample space for it. This is done to preserve the teeth’s proper alignment, while making sure the new teeth will erupt in its proper position.

A stainless steel band is placed temporarily around a permanent molar, with a stainless steel wire that loops out to extend to the second primary molar, leaving a space between them for the second premolar eruption.

The band and loop space maintainer are only helpful in maintaining a single missing tooth space. It may not be recommended for two or more succeeding missing teeth as it will be needing anchorage.

Distal Shoe Space Maintainers – 

Used to maintain the space of a primary second molar that has been lost before the eruption of the permanent first molar.

An unerupted permanent first molar drifts mesially within the alveolar bone if the primary second molar is lost prematurely. The result of the mesial drifts results in loss of arch length & possible impaction of the second premolar.

The distal shoe is usually retained with a band instead of a stainless steel crown so that it can be replaced by another type of space maintainer after the permanent first molar erupts. To be effective, the guide plane must extend into the alveolar process so that it contacts the permanent first molar approximately 1 mm below the mesial marginal ridge, at or before its emergence from the bone. 

Advantages :

• Single appointment
• No impression and model pouring
• Precise and no laboratory errors involved
• Universal bands decreases inventory
• Cost effective
• Very useful in sedation cases.

Key Features

• Universal band design
• Laser markings for tooth identification
• Short tube size for all type of cases
• 316L medical grade stainless steel
• Precrimped & Precontoured bands
• Nickel chromium laser brazing for better joint

Specifications

Material : Stainless Steel

Band Size :  24-42 , for upper right, upper left, lower right, and lower left primary and permanent molars.

Packaging

• Pack of 1

Directions for Use

Banding : Band with tube is selected by trial fitting. A band pusher and band adapter is use to fit and adapt the band around the tooth.

Select & Adjust Space Component : A wire component is selected to act as the spacer, straight and curved loop for band and loop space maintainer and the distal shoe for distal shoe space maintainer cases.

Insert Space Component & Check Fit: Slide the wire in the tube of the band. Place the band on the tooth and check if the space maintainer is fitting properly with space component resting on the supporting tooth.

Crimping band tube and space component: Keep e-crimper at the centre of the tube and do partial crimping intraorally. Remove the space maintainer and do final crimping extraorally.

Cementation: Clean and dry the band. Isolate and dry the tooth. Mix luting cement and apply on the inner surface of the band. Seat the band on the tooth using band pusher or band adapter. Remove excess cement after cement sets.

Additional Information

Country of Origin: India

Manufacturer:
Kids-e-Dental LLP
411, Akruti Arcade, J.P. Road, Opp. A.H. Wadia School, Andheri West, Mumbai – 400053, Maharashtra, India
Phone: +91 72899 99456

Packer:
Kids-e-Dental LLP
411, Akruti Arcade, J.P. Road, Opp. A.H. Wadia School, Andheri West, Mumbai – 400053, Maharashtra, India
Phone: +91 72899 99456

Marketed By:
Kids-e-Dental LLP
411, Akruti Arcade, J.P. Road, Opp. A.H. Wadia School, Andheri West, Mumbai – 400053, Maharashtra, India
Phone: +91 72899 99456