Ivoclar Te-Econom Plus Composite Refill

Description

Te-Econom Plus is a light-curing, radiopaque hybrid composite which has excellent physical properties and great polishability that makes it suitable for use in both anterior and posterior restorations. The high radiopacity allows easy identification in x-rays. Te-Econom Plus has a long working time that helps the clinical perform the dental procedure efficiently. 

 INDICATIONS

• Restorations of Classes I to V
• Esthetic anterior restorations
• Posterior restoration of stress-bearing areas.

 ADVANTAGES –  

• Excellent physical properties.
• Good polishability.
• High radiopacity.
• Long Working time.
• Proven Ivoclar Vivadent technology and quality.

Key Features

• Excellent physical properties
• Good polishability
• High radiopacity
• Long Working time
• Proven Ivoclar Vivadent technology and quality

Specifications

Composition:

• Te-Econom Plus consists of dimethacrylate and TEGDMA (22 wt%).
• The fillers include barium glass, ytterbium trifluoride, silicon dioxide and mixed oxide (76 wt% or 60 vol%).
• Additives, initiators, stabilizers and pigments are additional contents (2 wt%).
• The particle size of inorganic fillers is between 0.04 and 7 µm.
• The mean particle size is 850 nm.

Storage temperature 2–28 °C (36–82 °F)

Packaging

• 1 x 4gm syringe

Directions for Use

• Select the shade. For facilitated access to the treatment field, the flexible and patient-friendly mouth opener OptraGate can be used.
• Establish sufficient isolation, preferably with a rubber dam (complete isolation is ensured with, for example, the anatomically shaped OptraDam Plus).
• Prepare the cavity according to the requirements of the adhesive technique.
• Clean the cavity with water spray.
• Air dry the cavity.
• Apply a pulp protector (calcium hydroxide) if needed; only cover areas close to the pulp and subsequently apply a pressureresistant cement (e.g. Vivaglass Liner).
• Place a matrix (e.g. the selectively thinned OptraMatrix) and an interdental wedge, if required.
• Apply Eco-Etch on the enamel and then on dentin and allow a reaction time of 30 seconds on enamel and 15 seconds on dentin. After that, thoroughly rinse with water spray and dry the tooth surfaces with oil-free compressed air. Avoid dehydrating the dentin.
• Apply a generous amount of Te-Econom Bond on enamel and dentin, using the enclosed applicator brush. Brush the material gently into the dentin for 10 s. Next, evaporate any remaining solvent with a slow stream of air. Lightcure the adhesive according to the curing time recommendations below. Ensure complete coverage of the preparation surface.
• Apply Te-Econom Flow in layers of a max. of 2 mm and light cure according to the curing recommendations below. Apply Te-Econom Plus in layers of max. 2 mm and adapt/contour the material with a suitable instrument (e.g. OptraSculpt). The OptraContact instrument can be used to selectively position high-quality proximal contacts. Polymerize each layer individually according to the table below. Hold the light emission window as closely as possible to the surface of the restorative material.
• Finish the restoration with suitable finishers or fine diamonds. Subsequently, check the occlusion. Polish with silicone polishers (e.g. OptraPol Next Generation).

Additional Information

Country of Origin: Liechtenstein

Manufacturer:
Ivoclar Vivadent AG
Bendererstrasse 2, 9494 Schaan, Liechtenstein

Packer:
Ivoclar Vivadent AG
Bendererstrasse 2, 9494 Schaan, Liechtenstein

Imported By:
Ivoclar Vivadent India Pvt. Ltd.
Ground Floor and 1st Floor, Khandsa Village, Gurugram, Haryana, India
Phone: +91 72899 99456

Warranty & Service

• Warranty is not applicable for this product.