Dentsply Aquasil Ultra XLV Cartridge (Pack of 1)

Description

Aquasil Ultra is a Smart Wetting elastomeric impression material with excellent hydrophilic properties, dimensional accuracy, high tear strength and resistance to permanent deformation. 

Aquasil Ultra XLV Wash materials are available in 50 ml cartridges for manual application as well as digit cartridges for single-use application.

Key Features

• Exceptional wettability: accurate reproduction of preparations and hard and soft tissues.
• No bubbles, friction or error.
• Excellent mechanical resistance: easy removal of the impression without distortion or tearing.

Specifications

• Composition : 
• Polydimethylsiloxane polymer
• Polymethylhydrogen Siloxane
• Silicon Dioxide
• Sodium Aluminosilicate
• Organic Platinum Complex 
• Surfactant 
• Titanium Dioxide
• Metallic Oxide Pigments
• Peppermint Oil

Technical Specifications :

• Type 3: Light-bodied consistency: Aquasil Ultra XLV, Aquasil Ultra LV
• Type 2: Medium-bodied consistency: Aquasil Ultra Monophase, Aquasil Ultra Heavy
• Working Time (22°C/72°F) : 2’15″–2’45” (Regular set)
• Working Time (37°C/98°F) : 1’10” maximum (Maximum)
• Setting Time (Mouth Removal Time) :  5’00” from start of mix (Regular set)
• Percent Linear Dimensional Change : < 0.50
• Percent Recovery from deformation : .≥ 98
• Detail Reproduction : 20 microns

Packaging

• 4 x 50ml Cartridges
• 12 x Mixing tips

Directions for Use

• Insert cartridge into dispensing gun
• Bleed cartridge before installing new mixing tip
• Single phase impression technique – Assure hemostasis and clean the field with air water spray. Backfill the impression syringe or attach an intraoral tip to the end of the mixing tip. Dispense material into impression tray. Do not overfill tray. Simultaneous with tray loading, syringe completely around the preparation/abutment. Regular Set wash and tray material: Loaded tray must be inserted within 1 minute 10 seconds from time of first syringing of wash material intraorally. Minimum Removal Time (from the start of mix) : 5 minutes (Regular Set). If Regular Set Wash is used with Fast Set Tray material, Minimum Removal Time is 4 minutes from start of mix.
• Dual Phase two-step (“putty-wash”) Technique – Complete primary impression with Aquasil Ultra Xtra Tray, Aquasil Putty or Reprosil Tray material. Place one or more polyethylene plastic sheets over the impression material surface. This sheet creates the uniform spacing required for this technique. It also protects the surface from contamination. Insert filled tray into the mouth. Move tray slightly from side to side and back and forth. This creates the spacing for the wash material. Remove tray from the mouth when material has reached a rubbery consistency and set aside. Do not disturb
  impression until fully set. Remove polyethylene sheet, rinse impression with water and air dry. Simultaneous with tray loading, syringe (dentist) completely around the preparation/abutment. Insert filled tray into the mouth. 

Additional Information

Country of Origin: Italy

Manufacturer:
Zhermack S.p.A.
Via Bovazecchino, 100, 45021 Badia Polesine (RO), Italy

Packer:
Zhermack S.p.A.
Via Bovazecchino, 100, 45021 Badia Polesine (RO), Italy

Imported By:
Dentsply India Pvt. Ltd.
Plot No. 10, Sector 5, Manesar, Gurugram – 122052, Haryana, India
Phone: +91 72899 99456

Warranty & Service

• Warranty is not applicable for this product